|
|
For Sale: Cushman Bean Special Cub 3 HP
posted by Farmboy75 Batavia, IL 60510
Here is a nice original cushman bean special cub
3hp engine. Looks to be original paint and decals
with belt pulley and a brass carb. There is a hot
Wico mag on it, I had th ...
|
153
|
Good
|
$450.00
|
|
Thu March 18, 2010 5:29pm
|
|
|
Wanted: Ignitor and bracket assembly for magnito for 7hp Mcleod/Nelson bros
posted by Alltractorman Badger, Minnesota USA
Mounting holes are vertical,3"center to center.
Where the ignitor slides through,hole is about 1
7/8". Phone 2185283284 cory
|
25
|
None
|
n/a
|
|
Thu March 18, 2010 12:31am
|
|
|
Auction: TSX69 MARVEL SCHEBLER CARBURETOR
posted by dshirly Lethbridge, Alberta, Canada
For auction, a Marvel Schebler Carburetor , Model
,TSX 69, Bolt holes 2-3/8 c-c. everything there,
needs cleaning , needs boal gasket made. One small
crack in bottom of boal, ...
|
43
|
None
|
n/a
|
|
Wed March 17, 2010 4:22am
|
|
|
For Sale: Jacobsen-Bullseye.Splitdorf.Caterpillar magnetos
posted by John Raney  So. E. Michigan USA
Big Elkhart with a good gear and bracket for a
larger Jacobsen or Bulls Eye Rebuilt. $500..
HOT high tension Splitdorf RH rotation,bolt holes
are useable.Body has some cracki ...
|
122
|
Great
|
n/a
|
|
Wed March 17, 2010 3:19am
|
|
|
For Sale: INternaional harvester 2hp verticle motsinger bracket
posted by Gene Fisher Pilot Point, Texas
These brackets are new reproduction and are ready
to bolt on your two hp IHC vertical engine. The
mounting holes are side to side 4 inches and up
and down 4 1/2 inches so they ...
|
141
|
Great
|
$360.00
|
|
Tue March 16, 2010 4:26pm
|
|
|
For Sale: Schebler Brass Carb
posted by Tom Gosciminski Massachusetts
Nice little carb 1" bore and 2 3/8" hole centers.
( missing the needle valve and one ear is missing
from the air vale adjusting wing nut as seen in
the photo.)
|
98
|
unrated
|
$100.00
|
|
Mon March 15, 2010 4:15pm
|
|
|
For Sale: Gray 4 HP ? Crankguard
posted by Tom Gosciminski Massachusetts
This is a Very Heavy Cast Crankguard that I think
fits the 4 HP Gray Engine, the casting # inside
looks like F75-4 and the bolt hole centers are 6
1/2"
|
70
|
Great
|
$100.00
|
|
Mon March 15, 2010 4:00pm
|
|
|
Auction: Associated(?) 4 bolt Lo-Tension magneto hit miss engine
posted by Paul Spence New Jersey
Older Associated (maybe?) 4 Bolt Magneto-I don’t
know for sure. The 4 bolt base is 3 ¾” square and
the four 3/8” mounting holes are 2 ¾ C-C with good
threads. The gear shaft i ...
|
103
|
None
|
n/a
|
|
Sun March 14, 2010 1:36am
|
|
|
For Sale: 8 HP OE Stover rocker arm
posted by Ray Gardner Bandon, Oregon USA
These are new cast iron rocker arms, I have 5
left, They fit the 8 hp regular OE Stover, I left
the center hole undrilled because they all fit
different,I have 2 totally done.
|
45
|
Great
|
$75.00
|
|
Sun March 14, 2010 12:51am
|
|
|
For Sale: Wizard magneto & igniter
posted by Roger Kirschenman Nebraska USA
Wizard type 61 model 2 # 258259 magneto.The
mounting holes on the igniter are 3" C to C. bolt
holes are 1/2".This magneto has a big blue spark &
is ready to go to work.I will ...
|
187
|
Great
|
$500.00
|
|
Tue March 9, 2010 7:52pm
|
|
|
For Sale: John deere 1 1/2hp E
posted by Babs8070 Revere Mo
1923 john deere 1 1/2hp. It has new rings,gaskets
installed. I have new oil pan and fuel tank that
needs installed.Mag is hot but has a messed up
bolt hole. One weld on bottom ...
|
349
|
unrated
|
$575.00
|
|
Tue March 9, 2010 2:21pm
|
|
|
Wanted: mechanical governor lever for Briggs Model 8
posted by Kevin L. Denver, Pennsylvania
I'm looking for a mechanical governor lever for a
Briggs Model 8. I'll take the whole assembly if
necessary, but the lever broke and my assembly is
fine. The lever has 6 num ...
|
66
|
None
|
n/a
|
|
Tue March 9, 2010 1:18am
|
|
|
Wanted: Cart for BIG 6 Sandwich Engine
posted by John and Sherrel Bidne Senoia, Georgia
Looking for ORIGINAL cart for a BIG 6 Sandwich
Engine. Must be in GOOD condition with ALL
hardware. Rust OK--NO holes,broken or missing
spokes
Thanks!
John
770-842-7922
N ...
|
33
|
None
|
n/a
|
|
Sun March 7, 2010 11:35pm
|
|
|
For Sale: Early Victorian Steam Engine Toy Brass & Copper
posted by pjstoys Michigan City, Indiana
Early Victorian Steam Engine Toy. 18 inches tall x
6 inch wide base with a 4 inch O.D. Flywheel 1/2
inch wide. Original paint. Working Whistle.
Alcohol burner pot. Turns so fr ...
|
126
|
Great
|
$500.00
|
|
Sat March 6, 2010 11:26pm
|
|
|
Wanted: Pulley
posted by Bob Hanauer Albany, Minnesota USA
Looking for a pulley with a 2 1/2 inch shaft size
hole. Any ideas?
Thanks Bob "Fezzy" Hanauer
Thanks Harry
|
39
|
None
|
n/a
|
|
Sat March 6, 2010 3:15am
|
|
|
Wanted: Olds 3A inlet valve cage
posted by Oldsiron Southern Tablelands NSW Australia
Wanted: Inlet valve cage for 3A Olds with 3 bolt
holes for mounting as in photo, Thanks.
Chris Broers
Australia
|
119
|
None
|
n/a
|
|
Sat February 27, 2010 11:28am
|
|
|
For Sale: 1962 Reo raider engine
posted by carls315 fulton ny
here's a good 1962 Reo raider engine.- it was off
a reo,, reel type mower. #'s off mowers it was on
were, 418-AR, AND 421-AR.- ENGINE will run, as
when i put gas in plug hole ...
|
251
|
Good
|
$90.00
|
|
Sat February 27, 2010 12:50am
|
|
|
Wanted: Front cast steel wheels for a Twin City MT
posted by Mike Lau Glenville Minnesota USA
Looking for a pair of front cast steel wheels for
a Twin City MT, 3 hole bolt pattern, look like the
ones on unstyled A or G john deere also known as
texas sand wheels. They a ...
|
71
|
None
|
n/a
|
|
Fri February 26, 2010 3:02am
|
|
|
Wanted: Stover KE part
posted by Ray Gardner Bandon, Oregon USA
I am looking for stover KE 5 round hole flywheel
parts for Bill Walner, what an Engine man, In his
Ninety's and still working on Engines,Need valves
and springs, pushrod, wico ...
|
58
|
None
|
n/a
|
|
Wed February 24, 2010 2:17am
|
|
|
For Sale: briggs 89115 connecting rod NOS
posted by briggsnut Illinois USA
new old stock briggs and stratton connecting rod
part# 89115 this is same as rod # 290963 except
the rod im selling does not come with the dipper
has an extra oil hole on t ...
|
124
|
Great
|
$20.00
|
|
Sun February 21, 2010 1:37pm
|
