|
|
Auction: BEARING BABBIT LADLE
posted by Steve V. Annapolis, Maryland, U.S.A.
VINTAGE BABBIT & LEAD POURING LADLE
Up for auction is a Ladle used for melting
and pouring lead for pipe & Babbit for Engine
bearings. Made by "The Lake City ...
|
44
|
None
|
n/a
|
|
Wed January 7, 2009 12:52am
|
|
|
Wanted: From Ft. Wayne, IN to SDak.
posted by Dave Olson Rapid City, SD
I have a car hood in Ft. Wayne, IN that I need to
get to Rapid City, SD. (or anywhere close)The hood
is not perfect so I am not worried about a scratch
or ding - but I don't w ...
|
36
|
None
|
n/a
|
|
Tue January 6, 2009 5:36am
|
|
|
For Sale: 1918 Emerson Brantingham model A 12-20 for sale
posted by spedur carson city nevada
serial number 60012 makes it the 12th off the line
of ALL the model A 12-20s ever made & should be
the oldest still around. old restoration. you
hardley never see a early Emer ...
|
104
|
Good
|
n/a
|
|
Mon January 5, 2009 4:00am
|
|
|
For Sale: Building trusses for large storage building
posted by farmboy25 Larned Kansas USA
These trusses were built around 1925, they were
over the basket ball court of the city auditorium,
they have a dome ceiling, they are super heavy
duty and could support a lot ...
|
220
|
unrated
|
$10,000.00
|
|
Thu January 1, 2009 2:00am
|
|
|
Wanted: help in transport fairmont RR engine
posted by bobm reno nv
Folks what i have is a fairmont RR engine about
300 lbs coming from NW montana to reno NV but the
issue here is the ride i found is going east of me
salt lake city las vegas ...
|
53
|
None
|
n/a
|
|
Thu January 1, 2009 1:15am
|
|
|
For Sale: 1870s farr- Treffts steam engine
posted by spedur carson city nevada
large ,8 feet long. 56 inch fly wheel.compleate
except govener balls.
|
207
|
Fair
|
$2,500.00
|
|
Wed December 31, 2008 6:01pm
|
|
|
For Sale: 1908 Reid 40 hp engine, early & rare
posted by spedur carson city nevada
early 1908 40 hp Reid,no cracks or welds.98%
compleate.
|
122
|
unrated
|
$6,000.00
|
|
Wed December 31, 2008 5:52pm
|
|
|
Wanted: CH&E 5hp service manual or magneto type for this engine or any information. Just e-mail me with what you have and price.
posted by wendell langley Dexter City, Oh USA
Wanted: info on CH&E 5hp engine service manual
availability, magneto type used on this engine.
|
21
|
None
|
n/a
|
|
Wed December 31, 2008 3:47pm
|
|
|
Trade: I need MM-TC MT & MTA parts
posted by Tony Thompson Glenville, Minnesota, USA
May trade parts for Minneapolis Moline-Twin City
MT & MTA parts. I want skeleton and flat rear
steel, cast three bolt front steel with three bolt
hubs, and spoke front steel. ...
|
41
|
unrated
|
n/a
|
|
Mon December 29, 2008 2:02pm
|
|
|
Wanted: cylinder sleeve for IHC 11/2 Mc Cormick Model M.
posted by harold lee scofield Colorado City, Co. USA
Looking for a good cylinder sleeve for IHC Mc
Cormick 1 1/2 Hp Model M new or used.
|
51
|
None
|
n/a
|
|
Sun December 28, 2008 4:47pm
|
|
|
For Sale: 6.5 Nh onan
posted by harold lee scofield Colorado City, Co. USA
6.5KW Onan Generator needs choke coil but starts
and run very well. will put out 120-240 can
install remote control.
719-568-0798
|
246
|
Good
|
$700.00
|
|
Sat December 27, 2008 12:41am
|
|
|
Wanted: MM - Twin City MT & MTA steel wheels
posted by Tony Thompson Glenville, Minnesota, USA
I want to buy front and rear steel wheels for
Minneapolis Moline-Twin City MT & MTA. Would like
skeleton or flat rears, spoke or cast three lug
fronts with hubs. Also need ear ...
|
73
|
None
|
n/a
|
|
Thu December 25, 2008 4:09am
|
|
|
For Sale: Twin City 20-35 head
posted by Tony Thompson Glenville, Minnesota, USA
One head for early Twin City 20-35. This is an
early low compression head with large water ports
and part #AE3G. Has been cleaned and magnafluxed.
There are at least four dif ...
|
172
|
Good
|
$600.00
|
|
Mon December 22, 2008 2:49am
|
|
|
For Sale: 1929 twin city 27-44
posted by Steve Green Oregon, Illinois USA
tractor is on full with lugs has good manifolds
new water pump shaft correct rebuilt magneto.
serial # 250712 call for more info 815-234-8561
|
613
|
Good
|
$19,500.00
|
|
Wed December 10, 2008 4:47pm
|
|
|
Wanted: Christensen & Gilson parts
posted by brad churchill hager city, wi us
Looking for a piston for 4HP Christensen type FF
or Cast one, also carb or recast one.
Looking for muffler for 1/1.5 HP gilson Air
cooled.
Looking for 4 HP Lauson lawton muf ...
|
117
|
None
|
n/a
|
|
Tue November 25, 2008 2:44am
|
