|
|
Auction: David Bradley Continental AU-7B engine
posted by CaseyJoeS. McPherson, Kansas for college. Delmar, Maryland is home
Barn fresh Herman Nelson "prime mover assembly".
MFG part # ABT-101 Serial: 50417 . I'm not even
sure exactly what this would have been used for,
some sort of ventilation fan? ...
|
80
|
None
|
n/a
|
|
Sat March 20, 2010 2:31am
|
|
|
Wanted: Briggs PB intake valve
posted by Gary Do Girard, Ks., Crawford
Wanted to Buy: Intake valve assembly for Briggs
PB, also bolt for yoke clamp
|
24
|
None
|
n/a
|
|
Thu March 18, 2010 9:51pm
|
|
|
Wanted: Ignitor and bracket assembly for magnito for 7hp Mcleod/Nelson bros
posted by Alltractorman Badger, Minnesota USA
Mounting holes are vertical,3"center to center.
Where the ignitor slides through,hole is about 1
7/8". Phone 2185283284 cory
|
25
|
None
|
n/a
|
|
Thu March 18, 2010 12:31am
|
|
|
Wanted: F-20 brake spring cable assembly.
posted by Dave A. Lincoln, NE USA
I am in need of the brake spring/cable assembly
for my 1937 F-20. The cable bolt is the course
thread 3/8" one. Unfortunately I did a fine job of
ruining one of mine while try ...
|
36
|
None
|
n/a
|
|
Wed March 17, 2010 3:34am
|
|
|
Wanted: allis Chalmes plow adjustment lever LATCH
posted by Doug Oldenburg Homer, Nebraska USA
I am in need of 1 adjustment lever latch assembly
for an ALLIS CHALMERS pull type 2 bottom plow. I
could also use the lever at the top of the handle
that you squeeze when maki ...
|
55
|
None
|
n/a
|
|
Mon March 15, 2010 9:17pm
|
|
|
Wanted: Governor parts for Nelson built Hit and Miss Engine
posted by Chris Richards West Brookfield, Massachusetts USA
Need Governor Parts for Hit & Miss Nelson Bros 5hp
Jumbo (Sattley, Monarch,Maynard, etc.) I need the
arm that fits into the slip collar, the latch arm,
the latch plate, and th ...
|
54
|
None
|
n/a
|
|
Sun March 14, 2010 2:02pm
|
|
|
Wanted: IHC 4HP THROTTLE GOVERNED FAMOUS PARTS
posted by freshieslures Orange N.S.W. Australia
PARTS WANTED
MAGNETO TRIP ROD AND ECCENTRIC
THROTTLE ROD
EXHAUST VALVE PUSH ROD WITH 1/2 COMPRESSION ROD
AND ROLLER ASSEMBLY (Not sure of proper name so i
have included a ...
|
95
|
None
|
n/a
|
|
Sat March 13, 2010 4:27am
|
|
|
Wanted: Briggs model A early 5 digit air breather
posted by jcbwls Massena, New York USA
looking for a breather assembly for a early Briggs
model A interested in total assembly or just the
oil bath section
|
40
|
None
|
n/a
|
|
Wed March 10, 2010 11:28pm
|
|
|
Wanted: Need Governor Parts for Hit & Miss Nelson Bros 5hp Jumbo (Sattley, Monarch, etc.)
posted by Chris Richards West Brookfield, Massachusetts USA
Need Governor Parts for Hit & Miss Nelson Bros 5hp
Jumbo (Sattley, Monarch,Maynard, etc.) I need the
arm that fits into the slip collar, the latch arm,
the latch plate, and th ...
|
400
|
None
|
n/a
|
|
Tue March 9, 2010 11:39am
|
|
|
Wanted: mechanical governor lever for Briggs Model 8
posted by Kevin L. Denver, Pennsylvania
I'm looking for a mechanical governor lever for a
Briggs Model 8. I'll take the whole assembly if
necessary, but the lever broke and my assembly is
fine. The lever has 6 num ...
|
66
|
None
|
n/a
|
|
Tue March 9, 2010 1:18am
|
|
|
Wanted: Governer housing assembly for Wisconsin THD
posted by Dwride Near Flin Flon, Manitoba Canada
I need the governer housing along with the gear
and the small parts inside. I'll get the picture
of the engine up soon. Wisconsin 2 Cyl THD on a
10 KW Winco Generator.
|
83
|
None
|
n/a
|
|
Tue March 2, 2010 8:33pm
|
|
|
For Sale: 1956 DAVID BRADLEY AH-81 GEAR DRIVE CHAINSAW-RUNNING-watch videos
posted by davidbradley360 Drums, Pa. USA
1956 DAVID BRADLEY GEAR DRIVE CHAINSAW- THIS IS
THE BIG ONE POWERED BY THE AH-81 ENGINE- 130 CC- 8
CUBIC INCH- 8 HORSEPOWER- REALLY LONG BAR/CHAIN- 2
STROKE CARBURETED W/REED ...
|
250
|
Good
|
$1,000.00
|
|
Wed February 24, 2010 12:28pm
|
