Antique Engine and Tractor Ads

Wanted: Boiler for Frick engine
posted by wilsonfarms Clarksville, Tennessee

I am looking for a portable boiler for my 9 1/2 x 10 Frick steam engine. Good , bad , needs work, I will look at anything. please call 931-980-3170 thanks Derrick.
Enter Your Zip Code
Wed March 4, 2015 6:31pm
Wanted: Small early 2 ball steam governor.
posted by Lester Bowman 1 stars Modesto, CA

I need a small early steam governor similar to Gardner.It needs to be 1/4" or 3/8" NPT.An early 2 ball Pickering would work as well but it needs to be from about 1870-1880 per ...
227 Sat February 21, 2015 5:46am
Wanted: Case 50 crank side main bearing cap
posted by jimstockingfield worcester worcestershier united kingdom

does anyone have a main bearing cap for a Case 50hp steam tractor crank side
85 Fri February 20, 2015 7:57pm
Wanted: Ames No 4 engine parts and flywheels
posted by dgmills Acampo, California, USA

Looking for any parts or pieces for Ames No 4 engine, approx 60" curved spoke flywheels 3-1/4" bore. governor, nice cylinder oiler, any other literature and correct pieces Tha ...
108 Tue February 17, 2015 2:06pm
Wanted: dbl. spring traction engine gauge: 41/2-5" white face: 0-200 PSI with 5 PSI increments
posted by bengrizzley jackson, michigan :usa

need a double spring traction engine gauge for a rumbly steam engine. 4 1/2" -5" white face 0 - 200 PSI with 5PSI increments. also looking for a M-Farmall cultivators wit ...
182 Thu February 5, 2015 2:39am
Wanted: Prony Brake
posted by Lynnhomes01 New Albany, Indiana

Looking for a Prony brake to use at local shows. Would like it to be portable and able to use belt or PTO but would consider all.
374 Wed January 28, 2015 1:51am
Wanted: Pump parts for Keck Double cylinder
posted by Lynnhomes01 New Albany, Indiana

I am looking for the eccentric, pump and mounting brackets for a 22 HP Keck Gonnerman Double cylinder. I would be willing to copy someone's if they have a pattern I can use a ...
124 Wed January 28, 2015 1:49am
Wanted: Steam Engine Parts
posted by Ted Norman Northfield, Vermont USA

Looking for a "Waters" governor and some solid round oilers. These are for my vertical Haskins/Fitchburg steam engine. The horsepower of my engine is 4 or 5.
218 Sun January 4, 2015 10:27pm

Please read the Terms of Use for this system!

Register first!

Check your private messages.

For best results on Engine Ads, Register on Smokstak, confirm your email address and then Log IN here on Engine Ads. This will turn on many additional features, such as a contact seller button on the ads. Keep in mind that Enginads and Smokstak are two different web sites, but they now use only one registration system. Also, if you are running ads, Subscribers and Sponsors get more features and benefits on this site.
Only Sponsors may run ads for commercial products.

Find HELP with using our board by Clicking Here.

Be sure to check out the Business Card page for full-time suppliers of engines, parts and services. These are the folks that make this page possible, so please tell them that you saw their ad on Harry's Ad Pages! If their ad isn't here, tell them that it should be!

Enginads Smokstak Old-Engine

How these Gas Engine Ads began: CLICK HERE.

No portion of this page, text, images or code, may be copied, reproduced, published or distributed in any medium without the expressed written permission of the copyright holder.

Copyright 2006 - 2015 by
Harry Matthews
P.O. Box 5612
Sarasota, FL 34277